Sputtr.com | Alternative Search Engine

D1640

High-Performance Coatings Resins

High-Performance Coatings Resins Air Products and Chemicals, Inc., 7201 Hamilton Boulevard, Allentown, PA 18195-1501 Tel: (800) 345-3148, (610) 481-6799, Fax: (610) 481-4381, http://www.airproducts.com/epoxyadditives The information contained herein is offered without charge for use by ...

Radionics 9412 7412 User Guide with 720 Keypad

1 Fire Safety Residential fire is a leading cause of accidental death. Most fire related deaths occur at night when the occupants suffocate in their sleep from smoke and deadly gases, rather than from burns.

Coatings Testing Capabilities

... FTMS Method 3019 Storage Stability, FTMS Method 3022 Application and Film Formation Properties Brushing Properties Brushing Properties, FTMS Method 4321 Comparison of Brush Drag, Latex Paints, ASTM D4959 Visual Examination of Brushouts, ASTM D344 Dry Time Drying, Curing and Film Formation, ASTM D1640 Drying ...

Product Data/ Application Instructions

Drying time (ASTM D1640) @ 6 mils, DFT (hours) °F/°C 90/3270/2150/1032/0 touch 6 1 2 2 6 3 66 6 through 10 16 24 168 with 880 glassflake 12 18 26 192 Topcoat or recoat time minimum 1 6 1 81 0 1 72 Addition of 861 Accelerator does not change dry-to-touch or dry- through times but does accelerate cure for service.

DL430 & DL640 ASSEMBLY INSTRUCTIONS FOR THE NUT AND SCREW ...

... 5 16 lg bl0671 segment d19395!ok>vable jaw no dwg-f~s?1.~ polkr, i.0il; ux:i, ~ strip oiu.y ~ ** part #5 changed to dl640-97 wiper ** part!! 11 changed to dl640-331 wiper ring added part 1150 dl640-217 smalley ring added part 1151 dl640-231 smalley ring olfo'fd ~1 dl640-225a-30 03-0141 29 d1640-223 28 d1640 ...

SPKGS - [02581.PRN]

The test is the same as outlined in ASTM D1640 except that the lightest thumb pressure possible should be used. The thumb is turned through an angle of 90 degrees while lightly in contact with the film.

WBRD Traffic paint

• American Society for Testing and Materials (ASTM) Designations: D65, D93, D476, D522, D562, D711, D869, D1210, D1475, D1640, D2369, D2486, D3168, D3335, D3718, D3723, D3960, D4563, D5380, D6359, D6628, E70, E313, E1710, G151 and G154.

TECHNICAL INFORMATION

TYPICAL PERFORMANCE PROPERTIES Drying Time at 24 wet mils Dry to Touch (ASTM D1640-69, 5.4) 4 hours Dry, Through (ASTM D1640-69, 5.6) 12 hours Dry-to-recoat (ASTM D1640-69, 5.7) 12-24 hours Tensile Strength, psi @ 77°F, Break (ASTM D6083) 216 ± 100 psi @ 0°F 789 + 100 psi Elongation, % @ 77 ...

Liquid Thermoplastic Traffic Marking Paint

PASSES ~ Chemical & Physical Analysis Liquid Thermoplastic Traffic Marking Paint SMT - 300 (Meets TT-P-1952E Type III) Revised: 12/08 NOTE - Additional ASTM Test Methods employed were D1640, D2244, D3335, D3718, E-1347, G154.

Liquid Epoxy Coating 323C

... Typical Value Shyodu Gel Time (approximate pot life) 200 gm mass 75°F / 24˚C 104°F / 40˚C 18 Min 11 min Dry to Touch Time ASTM D1640 clause 7.5.2 41°F / 5˚C 75°F / 24˚C 122°F / 50˚C 7 hrs 1 hr 45 Min 26 min Approximate Back Fill Time (For additional information see Shore D Hardness Chart) ASTM D1640 clause ...